【CentOS7.9】yum 报错：Could not retrieve mirrorlist http://mirrorlist.centos.org

/ 默认分类 / 没有评论 / 234浏览

一、报错

报错内容如下

在使用 yum install -y xxx 的时候报错等等

[root@maruifu yum.repos.d]# yum install net-tools.x86_64
Loaded plugins: fastestmirror
Determining fastest mirrors
Could not retrieve mirrorlist http://mirrorlist.centos.org?arch=x86_64&release=7&repo=sclo-rh error was
14: curl#6 - "Could not resolve host: mirrorlist.centos.org; Unknown error"


 One of the configured repositories failed (Unknown),
 and yum doesn't have enough cached data to continue. At this point the only
 safe thing yum can do is fail. There are a few ways to work "fix" this:

     1. Contact the upstream for the repository and get them to fix the problem.

     2. Reconfigure the baseurl/etc. for the repository, to point to a working
        upstream. This is most often useful if you are using a newer
        distribution release than is supported by the repository (and the
        packages for the previous distribution release still work).

     3. Run the command with the repository temporarily disabled
            yum --disablerepo=<repoid> ...

     4. Disable the repository permanently, so yum won't use it by default. Yum
        will then just ignore the repository until you permanently enable it
        again or use --enablerepo for temporary usage:

            yum-config-manager --disable <repoid>
        or
            subscription-manager repos --disable=<repoid>

     5. Configure the failing repository to be skipped, if it is unavailable.
        Note that yum will try to contact the repo. when it runs most commands,
        so will have to try and fail each time (and thus. yum will be be much
        slower). If it is a very temporary problem though, this is often a nice
        compromise:

            yum-config-manager --save --setopt=<repoid>.skip_if_unavailable=true

Cannot find a valid baseurl for repo: centos-sclo-rh/x86_64

原因分析

我们的服务器没法访问外面的网络，所以我们需要配置镜像源

二、解决

进入目录

cd /etc/yum.repos.d

备份文件

# 备份这三个文件就行了（注意！！很多人只有 CentOS-Base.repo 文件，没有后两个，这也没问题，有几个备份几个，不用额外创建！）
CentOS-Base.repo

CentOS-SCLo-scl-rh.repo

CentOS-SCLo-scl.repo

修改文件

# 编辑 CentOS-Base.repo 文件
vi /etc/yum.repos.d/CentOS-Base.repo
#替换成以下内容
[base]
name=CentOS-$releasever - Base
baseurl=https://mirrors.aliyun.com/centos/$releasever/os/$basearch/
gpgcheck=1
gpgkey=https://mirrors.aliyun.com/centos/RPM-GPG-KEY-CentOS-7

[updates]
name=CentOS-$releasever - Updates
baseurl=https://mirrors.aliyun.com/centos/$releasever/updates/$basearch/
gpgcheck=1
gpgkey=https://mirrors.aliyun.com/centos/RPM-GPG-KEY-CentOS-7

[extras]
name=CentOS-$releasever - Extras
baseurl=https://mirrors.aliyun.com/centos/$releasever/extras/$basearch/
gpgcheck=1
gpgkey=https://mirrors.aliyun.com/centos/RPM-GPG-KEY-CentOS-7

[centosplus]
name=CentOS-$releasever - Plus
baseurl=https://mirrors.aliyun.com/centos/$releasever/centosplus/$basearch/
gpgcheck=1
enabled=0
gpgkey=https://mirrors.aliyun.com/centos/RPM-GPG-KEY-CentOS-7



# 编辑 CentOS-SCLo-scl-rh.repo 文件（如果没有这个文件，不用管）
vi /etc/yum.repos.d/CentOS-SCLo-scl-rh.repo
#替换成以下内容
[centos-sclo-rh]
name=CentOS-$releasever - SCLo rh
baseurl=https://mirrors.aliyun.com/centos/$releasever/sclo/$basearch/rh/
gpgcheck=1
enabled=1
gpgkey=https://mirrors.aliyun.com/centos/RPM-GPG-KEY-CentOS-7


#编辑 CentOS-SCLo-scl.repo 文件（如果没有这个文件，不用管）
vi /etc/yum.repos.d/CentOS-SCLo-scl.repo
#替换成以下内容
[centos-sclo-sclo]
name=CentOS-$releasever - SCLo sclo
baseurl=https://mirrors.aliyun.com/centos/$releasever/sclo/$basearch/sclo/
gpgcheck=1
enabled=1
gpgkey=https://mirrors.aliyun.com/centos/RPM-GPG-KEY-CentOS-7

清理 yum 缓存

yum clean all

重新生成 yum 缓存

yum makecache

请注意！如果在你之后的 yum install 过程中发生了 GPGKEY 报错，请参考这篇博客：

原文链接：https://blog.csdn.net/qq_43768851/article/details/140112143

本文由 小马哥 创作，采用 知识共享署名4.0 国际许可协议进行许可
本站文章除注明转载/出处外，均为本站原创或翻译，转载前请务必署名
最后编辑时间为: 2024/09/10 09:56

→ ← ↓ ↑